What Is the Recommended Standard for Measuring the Width of Galvanized Sheet

National standard for galvanized steel sheet?BSEN 10214-1995 continuously hot dip galvanized aluminum sheet and strip - Technical delivery conditions. BS EN 10215-1995 continuously hot dip aluminized galvanized steel sheet and strip - Technical delivery conditions. BS EN 10147-2000 continuously hot dip galvanized structural steel sheet and strip - Technical delivery conditions. BS 2858-1957 specification for steel plates for the manufacture of galvanized cans. BS 3083-1988 specification for ordinary hot dip galvanized and hot dip aluminum zinc corrugated steel plates.Recommended instruments for measuring the width of galvanized sheet

Lpbk50 width measuring instrument product introduction: galvanized sheet width measuring instrument is a non-contact on-line detection system for width measurement by using double barrel photoelectric probe. The double barrel photoelectric probe is composed of two groups of transmitting lenses and two groups of receiving lenses. It uses LED clean light source and CCD imaging method to measure the geometric dimension.Measuring principle of lpbk50 width gauge:Measuring principle of lpbk50 width meter

In the figure, the two transmitting lenses are provided with LED point light sources, and the light emitted by the point light sources is transformed into parallel beams through the lens and directed to the two receiving lenses respectively. The parallel beam is imaged on the photoelectric conversion element CCD chip through the lens in the receiving lens (Note: a transmitting lens and a receiving lens form a group of photoelectric probes). When the measured object passes through the field of view composed of two parallel lights, a virtual shadow will appear on the image of the photoelectric conversion element, and its widths are set as L1 and L2 respectively. After processing and calculating the electrical signal sent by the photoelectric conversion element, the dimensions B1 and B2 corresponding to L1 and L2 can be obtained. The width dimension a of the measured object can be obtained by adding B1 and B2 and the net spacing C between the two lenses.

In practical application, the net spacing C of the probe is the size calibrated with a standard ruler of fixed length. When the spacing of the probe is changed, the width of different specifications can be measured by taking into account the spacing change.Composition and connection mode of lpbk50 width gauge system: the width gauge system is a complete set of equipment integrating optical, mechanical, electronic circuit, communication and computer software technology. The whole system is mainly composed of width gauge body, main control cabinet, industrial computer, display, audible and visual alarm device, large LED display screen and so on.

In the whole system, the width gauge body and large LED display are installed on the measurement site, and the main control cabinet is placed in the control room. The width measuring instrument is connected with the main control cabinet by a three core power line and an optical cable. The power supply and power off of the width measuring instrument are realized by the main control cabinet through the power line, and the data signal of the width measuring instrument is transmitted to the main control cabinet through the optical cable. The power supply of the large LED display screen is also led out from the main control cabinet. The power supply and power failure of the display screen are synchronized with the start and stop of the main control cabinet. The display data of the display screen is sent to the display screen by the main control cabinet through optical cable.

Lpbk50 width measuring instrument software system:

(1) Interface display contents: width standard value, positive and negative tolerance, real-time width value, width deviation value, etc. (2) Curve fitting function: it can fit the width change fluctuation curve and temperature change fluctuation curve. (3) Product parameter setting: you can set product specifications, positive and negative tolerances and other parameters. (4) Out of tolerance alarm function: when the width exceeds the set tolerance, it is an audible and visual alarm. (5) Calibration function: when the measurement error is too large, put it into the standard ruler and calibrate it. (6) Automatic adjustment function of probe spacing: automatically adjust probe spacing when switching width specifications. (7) manual adjustment function of measuring head distance: adjusting the distance between probe heads after opening and closing distance. (8) System parameter setting: serial port, probe head, refresh frequency and other parameters can be set. (9) Data storage function: automatic storage of measurement data. The storage records can be opened by measurement software or converted into excel format.

fqj